Showing posts with label copper. Show all posts
Showing posts with label copper. Show all posts

Sunday, March 2, 2025

copper toy masks for painting

 







Eric and Chung sent these videos to me. I had no idea that this was how masks and spray painting on toys were done. It's fascinating. It also provides a real world application of copper sheetmetal forms. Eric and I discussed the fact that these are most likely die formed copper sections made from the original design of the toy. It makes me want to explore more involving 3D printed (full infill) dies like we have been doing in my classes. I just want to create a more complex form than what we have doing. For the moment, we have just been doing shallow sinking forms that are similar to spoon or bowl shapes. I need to work on this during the summer.




Thursday, February 13, 2025

radiators

 


I've been thinking about radiators lately. I'm not certain why but this is a good video to explain the process of making a radiator. I wonder if any of the knowledge or thoughts on construction of a radiator came from steam boilers? I'm just thinking through how we get from one place to another with technology and how we take something for granted once it works. I just hadn't given a lot of thought to what I would need to do to build a radiator from scratch.

I came across this on the Brassworks website.

Ford's Cooling System 

explained by Henry Ford

The Ford Cooling System
How is the Engine cooled?Answer No. 35

The heat generated by the constant explosions in the engine would soon overheat and ruin the engine, were it not cooled by some artificial means. The Ford engine is cooled by the circulation of water in jackets around the cylinders. The heat is extracted from the water by its passing through the thin metal tubing of the radiator---to which are attached scientifically worked out fins, which assist in the rapid radiation of the heat. The fan, just back of the radiator, sucks the air around the tubing- around which the air is also driven by the forward movement of the car. The belt should be inspected frequently and tightened when necessary---not too tight, however---by means of the adjusting screw in the fan bracket. Take up the slack till the fan starts to bind when turned by hand. 

How does the Water circulate?Answer No. 36

The cooling apparatus of the Ford car is known as the Thermo-siphon system. It acts on the principle that hot water seeks a higher level than cold water---consequently when the water reaches a certain heat, approximately 180 degrees Fahrenheit, circulation commences and the water flows from the lower radiator outlet pipe up through the water jackets, into the upper radiator water tank, and down through the tubes to the lower tank, to repeat the process.

What are the causes of Overheating?Answer No. 37

(1) Carbonized cylinders;

(2) too much driving on low speed;

(3) spark retarded too far;

(4) poor ignition;

(5) not enough or poor grade oil;

(6) racing motor;

(7) clogged muffler;

(8) improper carburetor adjustment;

(9) fan not working properly on account of broken or slipping belt;

(10) improper circulation of water due to clogged or jammed radiator tubes, leaky connections or low water.

What should be done when the Radiator overheats?Answer No. 38

Keep the radiator full. Don't get alarmed if it boils occasionally---especially in driving through mud and deep sand or up long hills in extremely warm weather. Remember that the engine develops the greatest efficiency when the water is heated nearly to the boiling point. But if there is persistent overheating when the motor is working under ordinary conditions---find the cause of the trouble and remedy it. The chances are that the difficulty lies in improper driving or carbonized cylinders. Perhaps twisting the fan blades at a greater angle to produce more suction may bring desired results. By reference to the proper division of this book each of the causes which contribute to an overheated radiator is treated and remedies suggested. No trouble can result from the filling of a heated radiator with cold water---providing the water system is not entirely empty---in which case the motor should be allowed to cool before the cold water is introduced. 

How about cleaning the Radiator?>Answer No. 39

The entire circulating system should be thoroughly flushed out occasionally. To do this properly, the radiator inlet and outlet hose should be disconnected, and the radiator flushed out by allowing the water to enter the filler neck at ordinary pressure, from whence it will flow down through the tubes and out at the drain cock and hose. The water jackets can be flushed out in the same manner. Simply allow the water to enter into the cylinder head connection and to flow through the water jackets and out at the side inlet connection. 

Will the Radiator freeze in winter?Answer No. 40

Yes, unless an anti-freezing solution is used in the circulating system you are bound to experience trouble. As the circulation does not commence until the water becomes heated, it is apt to freeze at low temperatures before it commences to circulate. In case any of the radiator tubes happen to be plugged or jammed they are bound to freeze and burst open if the driver undertakes to get along without using a non-freezing solution. Wood or denatured alcohol can be used to good advantage. The following table gives the freezing points of solutions containing different percentages of alcohol:

  • 20% solution freezes at 15 degrees above zero.
  • 30% solution freezes at 8 degrees below zero.
  • 50% solution freezes at 34 degrees below zero.

A solution composed of 60% water, 10% glycerin and 30% alcohol is commonly used, its freezing point being about 8 degrees below zero.

On account of evaporation fresh alcohol must be added frequently in order to maintain the proper solution. 

How are leaks and jams in the Radiator repaired?Answer No. 41

A small leak may be temporarily repaired by applying brown soap or white lead---but the repair should be made permanent with solder as soon as possible. A jammed radiator tube is a more serious affair. While the stopping of one tube does not seriously interfere with the circulation, it is bound to cause trouble sooner or later---and the tube will freeze in cold weather. Cut the tube an inch above and below the jam and insert a new piece, soldering the connections. If the entire radiator is badly jammed or broken it would probably be advisable to install a new one.




Sunday, January 5, 2025

more bucyrus

 


A good video about Bucyrus copper kettles. There is more detail on the process in this video.

Tuesday, December 31, 2024

making apple butter

 


If you're wondering about the making of apple butter with a copper kettle. The images of the family farm in this video are gorgeous. I spent some time on this person's you tube channel. The Pennsylvania Dutch sayings video that she posted is very interesting. I love hearing about the history of people from all over our country. I believe that we need more of this kind of education in our schools; learning about how things have progressed and where we all came from. History has been forgotten in favor of the next fad or news blip. This make me yearn for 100 acres of land in the midwest.

bucyrus copper kettle works

 





photos from Erin Gottsacker

This is an article is about the Bucyrus Copper Kettle Works. It would be awesome to take a tour of this place.




forming stake pattern












Hans loaned me some old (and giant) forming stake patterns a week or two ago. I believe that he said they came out of the Bucyrus Copper Kettle Works in Bucyrus, Ohio. He was able to secure several tools and patterns from this company when he was organizing the Pettingell Machine Company which he now owns. Bucyrus Copper Kettle Works is still one of the last companies in the country that still makes hammered copper vessels and they have been in business since 1874. 

These forming stake patterns are unique in that the top plate of each pattern is removable. I believe that this would aid in casting several different forming stakes with different compound curvature. I have already 3D modeled one of the stakes and I have created a separate top section that I can create different top curvatures from. I am looking forward to casting a few of these this year.



Wednesday, June 5, 2024

garagiste and pooper
























garagiste

a term used by Enzo Ferrari in the early days of Formula One racing, describing the privateer race teams, primarily the British ones

Enzo Ferrari coined the term "garagiste," to scornfully describe the small back-yard racing teams that dared to challenge a grand Constructor like himself.

In the late 50's and early 60’s a growing number of little British ‘privateer’ Formula One teams popped up from nowhere to compete against the big factory teams of Ferrari and Maserati. They didn’t have flash branding, big headquarters and massive budgets.

What they did have were innovative ideas, new designs and a total lack of respect for doing things “the traditional way”.

The old guard didn’t particularly like this and Enzo Ferrari disparagingly labelled them “garagiste”.

Regardless of their humble beginnings the Garagiste started winning. They started winning..a lot.

Ken Miles’ Infamous Pooper

When the 550 was replaced with the much-improved 550A, John von Neumann had trouble procuring one of the in-demand new cars for his racing stable. So driver Ken Miles called upon his days building custom specials and had von Neumann order a light and nimble Cooper race car without a motor. After a Porsche 550 engine was installed and modifications were made with the help of fabricator Dick Troutman, the “Pooper” proved nearly unbeatable in its class. Porsche took notice and, dismayed that the homebuilt special was beating their factory cars, quickly delivered a 550A to von Neumann’s shop, putting an end to the Pooper’s reign.

OK, now imagine building a replica Cooper Type 39 frame and dropping a 2 liter VW engine with upright cooling with flipped transaxle and simple transverse leaf spring suspsion. Build an aluminum body and see how lightweight you can build the entire thing. Try to get the power to weight ratio "right" and you'd have a proper race car...


Thursday, February 27, 2020

Followers