Showing posts with label Toyota. Show all posts
Showing posts with label Toyota. Show all posts

Sunday, January 5, 2025

fj/hj 47 front driveshaft















Putting the transfer case from the 4Runner in the FJ40 has caused all sorts of issues. I knew this would be the case since the stock FJ40 is passenger side differential and the 4Runner/Tacoma is driver’s side differential. I solved that issue by cutting the front axle pumpkin off, notching the housing for the 3rd member flipping the drain plug from bottom to top; which became the bottom when I flipped the axle, and cutting and flipping the end knuckles. Again this axle issue was solved a long time ago. But that still doesn’t connect everything to provide 4wd. 

The front driveshaft needed to have a carrier bearing to work with the leaf spring from axle since the driveline would be flexing. Yesterday I decided to tackle this project. I used a two piece rear Tacoma driveshaft and cut it up to make all the pieces I would need. I’ve gotten half way decent at making new custom length driveshafts. Luckily these are smaller sections, so I can true them and set them up for welding on my 13” South Bend lathe. Using the rear driveshaft for my front driveshaft allowed me to have larger u-joints for strength but it then caused an issue with the small bolt pattern on the pinion flange from the stock FJ40 axle. 

My neighbor assisted me on this and made a plate that I could drop the stock flange into and weld. Then I recut the larger profile of the plate and drilled holes to match the new custom driveshaft flange. I could have left the pinion flange alone and used a conversion u-joint but I thought keeping all the same u-joints was a better move. I made a mount for the carrier bearing that comes off of the transmission crossmember. It all turned out well. 

I now know that my front section of driveshaft is the correct length (after my initial guess) and now I can fully weld this. One step closer…



 

Wednesday, December 25, 2024

scratch built toyota fj47 "troopy"
















Sometimes you get excited about a project and your hands can't move fast enough for brain. Your imagination and creativity take over and supercharges your senses and makes you skip steps and make stupid decisions. It's sometime difficult to slow down and do things right. 

During the pandemic I started to visualize and dream about owning a Toyota Troopy or FJ/HJ 47. I was starting to see some of these showing up in the States since they were now legal to import from Australia or South America, but I still couldn't afford what these rusted out hunks were selling for.  I had come across some extra parts when I was restoring an earlier project FJ40 and I happened to have a rusted out frame and another good frame, so my brain started working overtime. I had some time off work due to the pademic and in a few weeks I had a frame cut upand pieced together and I started going to town mocking up rusting sheetmetal. I kept telling myself that I was just trying to see what it might look like and just wanted to see if I had the parts to make it all come together. I stalled out when I was trying to figure out what drivetrain I would put in it.

Once the pademic was over, my neighbor came over and saw it and we were talking about drivetrains and he said that he had a Toyota 4 Runner that was rusted out but that had a good engine and trans that he would give me. The wheels started turning again and In a couple of days I had a Toyota 5VZ 3.4L leveled up and had the transmission and transfer case mounted. I even got the crossmembers welded in and started thinking about a gas tank solution. The front axle on a stock FJ is passenger side diff but the 97 4Runner requires driver's side dif to make the transfer case hookup. My neighbor and I had talked this over originally and he was urging me to use the 4runner frame, but I really wanted the solid axle setup and the measurements would require widening the FJ40 body which I think ruins the proportions. Would you think that this hurdle would have stalled me out, but I I figured I could take the stock from axle, cut the dif housing off, cut the axle knuckle end off and flip it all around and weld it back in place. One might think that it's just a simple flip of the axle, but that would give send you in reverse when trying to drive forward. Anyway, I go through this and I was one step closer.

Now in my mind, I kept hitting a hurdle as the logical side of my brain knew that I had not previously buttoned up all frame issue from the initial stretch and moving forward with the body fitment didn't make sense until I had had a proper rolling chassis. I had gotten parts for a disc brake conversion, but the frame just wasn't a strong foundation to build on. 

That brings me to this week. Now that I was off school, I decided that I needed to strip the body back off and address all of the issues with the frame. I could box the frame while I was at it, figure out my gas tanks mounts, reinforce any of the crossmembers, put in my front carrier bearing for the front driveshaft, paint the frame, run brake lines, run fuel lines, install power steering, and finalize the disc brakes, axle rebuilds, and get this mega long frame into a rolling chassis.

In the past few days: 
I made box sections for the middle of the frame where I added 26" of frame. I cut holes similar to the stock frame in these sections and got them tacked in place. I finalized the position of my chevy blazer gas tank, adapted the 4runner style sending unit and made a crossmember and mounts for the tank. I still need to make lower straps, but I'm close on this.

Welded nuts to the inside of the frame for the bump-stop mounts.

I made plate sections to box in the frame over the axles and got them welded in.

I ordered some POR 15 to paint the frame and I started cleaning up surface rust on the frame.

I finished welding in the motor mounts and fully welding the crossmember for the transmission mount.

After today, I still need to:
Make some more plates to box in the rear section that is added onto the frame ( I have made templates for these).
Finish welding the diagonal braces at the rear of the frame.
Patch any unused holes.
Weld in a plate for the power steering box mount.
Take a stab at re-arching the leaf springs and cleaning each individual leaf in all of the leaf packs.
Machine my Chevy truck brake rotors.
Make rear caliper mounts for the Mote Carlo brake calipers

Rebuild the axles
Check the 3rd member gear lash.

Order a saginaw steering box
Order a set of shocks
Order new leaf spring bushings
Order a new set of tires
Order brake line material
Order axle seal kit and possibly axle bearings.

I know this doesn't look like much but it feels like a big step in the right direction. There's still a lot to do, but I feel like I've at least slowed my brain down a bit and I'm working on getting the foundation right before moving onto the body. However, I'm excited to get to the sheetmetal because I'm planning on making some tooling so I can recreate some of the sheetmetal from scratch so that the final result is better crafted. I'm stocked to get all the welding on the frame finished so I can lift the drivetrain out with my hoist and I can drop the axles and do a full on quality paint job on it. I'm trying to think of the frame like a piece of sculpture, so I'm going to try and smooth everything on it.




 

Thursday, November 1, 2018

fj40 photgrammetry











I've been playing with Autodesk Recap again as I prepared for a visiting artist gig I was doing at ECU. I decided to try a quick scan of my FJ40 in the driveway. This was made with maybe 60 still photographs using my Nikon D90. I only took one level of photos too. This would have been even better if I had taken more photos. It's amazing how well the program deals with large forms. it still amazes me. You might remember the scan I did with my 240Z back when the program was called Momento and the UWM panther using Recap.



Thursday, September 20, 2018

Wednesday, March 14, 2018

fj40 brakes



The FJ40 has been getting driven quite a bit. I had some issues with my brakes during the shakedown runs and a fuel line used for a vacuum line, but after changing that out things were o.k. except for a little fade that I thought was due to air in the line. Brakes that aren't up to snuff can be a pain, but here in the mountains it's unnerving. After bleeding the lines, it's not any better. I'm running a late model brake booster and master cylinder so diagnosing this isn't straight forward. I have a brake booster with three vacuum ports though so I think that may be my problem. I have two ports plugged and one running to the intake. I think maybe the other two ports control separate chambers in the booster rather than it being one big chamber (as I first thought). I'm going to try running all of the lines together to the intake and see if that solves my problem. If anyone fully understands the inner workings of brake boosters feel free to educate me.



another snow day







We received 7 inches of snow at our house last night. The University cancelled as I was blowing snow off of the driveway; so I could get to work. We (Jill and I) finished the driveway job and I cleared my neighbor's drive and had Noah finish that job. We were able to get into town fine to get some supplies. The highways were mostly clear and Boone looked like it had gotten less snow than us. The kids have now had over 20 snow days this year. Looks like it will be a late school year well into June. This is severely throwing off my teaching schedule, but I'll be able to salvage things as long as the weather clears up.



Sunday, February 18, 2018

fj40 daily driver



I drove the FJ40 to work all last week. It did great on these longer shake down runs and I just have a few minor issues to take care of. The brake booster vacuum line actually was fuel line so I have some issues once and while with a tight brake pedal, so until I source some proper vacuum line, I'm off the road. I had an annoying oil leak that I was worried was a rear main seal, but instead is the oil pan drain plug and damaged threads on the pan. I have a new oil pan gasket and just decided to put a new pan on it since they're so cheap. I'll repair the old pan though to keep as a backup. So far things have been fun with this old beast. I get a lot of looks while driving and have already had multiple offers to buy it. It's fun to drive to the studio too and great for hauling stuff. It drives like a tractor and really reminds me of my sidecar. Pure utility; but perfect for the part of the country I live in.



Saturday, January 27, 2018

fj40 shakedown runs




I've been taking the FJ40 on short shake down drives these last couple weeks. Adjusting cables, wiring and misc. things as they pop up. This early relationship building stuff wears me out. I just want to be able to have instant trust and confidence, but these things take time. I'm reminded of that anytime I build something.



Followers